Kohler 100kW Natural Gas Standby Generator & Transfer Switch
Generator: model #100RZ282, s/n: 3382658, SPEC. PA-187441-82N, 60 HZ. 1800 RPM
Three phase 100 KW, 125 KVA, 120/240V
Engine Ford model #LSG-8751-6005-A, s/n: 27794 R-28-RK V8, S.O./Options 3900, model code #HZA-3900-QBA. Hours 1,147
Includes a KOHLER Power System, Transfer Switch: MPAC 1500 Decision-Maker, part #ZCS-668641-400 14H 14J 23G 2468A 34J 34Z, S/N #K70692, volts 208 amps 400 3-phase 4-wires hertz-60 poles-4.
Was in good working condition when it recently removed from service, and is being sold due to normal rotation of equipment
Current working condition is unknown.
Sold AS IS
Good luck bidding
The following general information is web-sourced and may contain variances from the subject unit:
Kohler commercial/industrial 100 kW natural gas standby power system built in the mid-to-late 1990s, consisting of a heavy-duty Kohler generator powered by a Ford V8 industrial engine and paired with a newer-generation 400-amp Kohler automatic transfer switch (ATS).
Generator Specifications (Kohler 100RZ282)
The Kohler 100RZ282 is a stationary, liquid-cooled commercial standby generator. Because the Ford LSG-875 engine was phased out in early 2000, this unit dates to roughly 1994–1999.
- Power Output. Rated at 100 kW / 125 kVA (0.8 power factor) on natural gas. If converted to LP gas, output derates slightly to roughly 90 kW.
- Electrical Configuration. Set up for 120/240V, 3-phase (four-wire delta) at 60 Hz. The alternator is typically a 12-lead reconnectable unit, meaning an electrician can rewire it for 120/208V or 277/480V 3-phase if needed.
- Spec Number (PA-187441-82N). Kohler’s factory build sheet code defining the exact alternator, control panel (typically a Decision-Maker 3+ or 340), and enclosure configuration.
- Approximate Size & Weight. An open-skid unit weighs around 2,290 lbs wet and measures roughly 88" L × 34" W × 51" H. Units with full weather/sound enclosures are significantly larger and heavier.
Engine Details (Ford LSG-875I-6005-A)
- Engine Architecture. A 7.5-liter (460 cubic inch) cast-iron V8 based on Ford's heavy-duty 460 big-block, governed at 1,800 RPM to maintain 60 Hz electrical frequency.
- Turbocharged Induction. To reach 100 kW on natural gas at 1,800 RPM, Kohler fitted this engine with a turbocharger (commonly an IHI RHB6 unit).
- Key Features. Built with hardened exhaust valve seats, hypereutectic pistons, and breakerless electronic ignition to handle the higher combustion temperatures and dry nature of gaseous fuels.
- Maintenance Specs. Holds roughly 8.5 liters (9 quarts) of oil and uses a standard liquid-cooled radiator system.
Transfer Switch (Kohler MPAC 1500)
The Kohler Decision-Maker MPAC 1500 is a microprocessor-controlled automatic transfer switch. Because the MPAC 1500 controller platform was introduced years after the 100RZ series, this switch was likely upgraded or paired with the generator later in its service life.
- Electrical Rating. Rated for 400 Amps, 3-phase, 4-wire, 60 Hz.
- 4-Pole Configuration. Unlike standard 3-pole switches, a 4-pole switch actively switches the neutral conductor alongside the three hot phases. This is used for separately derived systems (such as ground-fault protection schemes or specific healthcare/commercial code requirements).
- Controller Features. Includes a 4×20 backlit LCD screen, programmable exercise timers, a 100-event history log, and Modbus RTU/TCP communication ports for remote building monitoring.
- Option Codes (14H 14J 23G 2468A 34J 34Z). Kohler factory accessory codes designating specific installed modules such as auxiliary position contacts, programmable I/O relays, anti-condensation heaters, or engine start/exerciser options.
Before installing or wiring these two pieces of equipment together, pay close attention to their voltage configurations:
- Generator Voltage. Currently configured for 120/240V 3-phase (a high-leg delta configuration).
- Transfer Switch Voltage. Currently configured for 208V (120/208V) 3-phase (a wye configuration).
Terms of Sale:
All sales are final. No refunds will be issued. This item is being sold as is, where is, with no warranty, expressed written or implied. The seller shall not be responsible for the correct description, authenticity, genuineness, or defects herein, and makes no warranty in connection therewith. No allowance or set aside will be made on account of any incorrectness, imperfection, defect or damage. Any descriptions or representations are for identification purposes only and are not to be construed as a warranty of any type. It is the responsibility of the buyer to have thoroughly inspected this item and to have satisfied himself or herself as to the condition and value and to bid based upon that judgment solely. The seller shall and will make every reasonable effort to disclose any known defects associated with this item at the buyer request prior to the close of sale. Seller assumes no responsibility for any repairs regardless of any oral statements about the item. Seller is NOT responsible for providing tools or heavy equipment to aid in removal. Items left on seller premises after this removal deadline will revert back to possession of the seller, with no refund.
